So, you’ve tried every way possible to get your ATV started, but to no avail. You’ve even replaced the battery, and it won’t start. What’s going on? In this article, we’ll show you how to bypass neutral safety switch on ATV so you can get it up and running again.
The most likely culprit is the neutral safety switch. This safety device is designed to keep the ATV from starting in gear. It’s usually located on the foot pedal, and it’s easy to bypass if you know how.
The problem may be the neutral safety switch if you’re having trouble starting your ATV. This small but essential piece of equipment ensures you can only start in neutral gear positions. If it’s not working correctly, you may not be able to start the engine.
We will show you how to bypass neutral safety switch on ATV. It’s a pretty simple process, but it’s crucial that you take your time and do it properly. Let’s get started.
What is a Neutral Safety Switch?
The neutral safety switch is a component on your ATV that’s responsible for preventing it from starting in gear. It does this by detecting whether the transmission is in gear or not. It guards against the forward gear shift of your vehicle while you are riding. It will lock the gearshift in neutral, so it cannot be moved to any other position. This prevents you from accidentally shifting into reverse while driving down the road.
If the switch isn’t working correctly, it can cause your ATV to start up while you’re shifting gears, which can be dangerous. That’s why it’s essential to know how to bypass neutral safety switch on your automatic transmission on ATV if it’s not functioning correctly.
There are a few ways to do this, but one of the most common methods is to use a paper clip or a wire to short the two terminals on the switch. This will trick the switch into thinking that the transmission is neutral, allowing your ATV to start.
What Does a Neutral Safety Switch Do?
The neutral safety switch is a safety device that prevents an ATV from moving forward if the vehicle is in neutral.
It allows you to park your ATV safely without putting any strain on your vehicle’s transmission.
The neutral safety switch is located near the clutch pedal on an ATV. It has three positions: off, on, and off. When in the off position, there are no pins or contacts in place; no voltage will flow through them, meaning no power will be sent to your vehicle’s engine.
When you move your foot from the clutch pedal to the accelerator pedal of your ATV, it will automatically move into gear by itself without you having to use any force. The neutral safety switch will not allow this to happen until you release pressure from both pedals and return them to their original position.
If someone falls off their ATV and the engine dies, they could be in trouble. A neutral safety switch can prevent this by automatically cutting power when the rider lets go of the throttle but keep their foot on the brake.
This is especially important for kids who might not know how to ride correctly or for people who are more comfortable riding with one hand on the brake lever rather than two.
Reasons to Do a Neutral Safety Switch Bypass
There are many reasons to bypass the neutral safety switch on an ATV.
The most common reason is to allow the engine to crank without engaging the clutch. This can be used when starting in cold weather or using a starter motor.
Another reason is if you have a mechanical problem with your transmission and need it to spin without engaging the clutch. In this case, you would want to bypass the neutral safety switch so that you can use your transmission emergency stop button. Alternatively, you could remove it entirely from the bike.
It also helps to prevent you from accidentally putting your ATV in gear and starting it. This is a helpful feature, but you can also bypass it. Bypassing this safety switch allows you to move the ATV without worrying about moving the parking brake.
In other words, if you’re using an ATV with a neutral safety switch and it’s not working correctly, you can fix it by bypassing it.
You should bypass the neutral safety switch on your ATV or UTV because it can cause many problems. The neutral safety switch keeps your vehicle in gear as long as you are not moving forward, and this can be dangerous if you are bumping around in a parking lot.
In addition, if you have an automatic transmission and have not disengaged the neutral safety switch, this will keep your vehicle in gear.
If you have an automatic transmission and do not bypass the neutral safety switch, your ATV or UTV may not shift out of park when you release the shift lever. This is because the transmission does not know that it is going into reverse unless someone has pressed their foot on the brake pedal.
How to Bypass Neutral Safety Switch on ATV
This switch must be bypassed to safely ride on two-wheel ATVs and UTVs, some four-wheel ATVs, and all off-road vehicles. So, you need to know how to bypass neutral safety switch automatic transmission.
In order to bypass the neutral safety switch on your ATV, you’ll need to do a couple of things.
Step 1: Unplug the battery from the ATV.
Step 2: Remove the two bolts on each side of the handlebar switch located under the handlebars. Then remove the two bolts holding it to the frame.
Step 3: Gently pull the switch until it pops out of its housing. Pulling too hard could damage it.
Step 4: Press on both sides of the switch and bend it back into place, snapping into place like a spring. You can now use this as a replacement part if needed!
Once you’ve done that, you’re good to go—be careful not to hit the switch by accident, or you’ll find yourself in a world of trouble.
Alternatively, you will need to short the neutral safety switch on your ATV.
Here’s what you need:
- A length of wire with a gauge-stranded copper wire.
- A small screwdriver and a pair of pliers (or vice grips).
- The ATV’s neutral safety switch is located under the seat or in between the seats on most models.
These are the steps to follow to short the neutral safety switch, thereby bypassing it:
STEP 1#: Remove the seat from the vehicle and remove the headlight.
STEP 2#: Remove the gas cap and remove any debris from around it.
STEP 3#: Locate the neutral safety switch on your ATV’s rear above the rear wheel axle assembly.
STEP 4#: Disconnect the black wire with a 12-volt battery charger or jumper wire by squeezing it between your fingers and pushing it down with a screwdriver. You can also use another tool until it pops up slightly out of its socket in the housing where it is attached to the switch housing itself. Pull out with pliers if necessary to disconnect.
STEP 5#: Attach your 12-volt battery charger or jumper wire directly to one end of your black wire and attach its positive terminal to one side of a screwdriver blade. This will allow you to quickly push down on both sides of this black ground wire at once for better contact resistance when trying to short out this particular switch on your ATV.
STEP 6#: Attach your other end of this black wire directly. Place a jumper wire between the two terminals labeled “B” and “N”. This will allow you to control whether or not your ATV is in gear or neutral when you engage your clutch pedal.
STEP 7#: Now, replace your seat and tighten up all four bolts again, making sure not to overtighten them as they could damage your bike.
Consequences of Bypassing the Neutral Safety Switch on Your ATV
Let’s say you’ve decided that you want to bypass the neutral safety switch on your ATV. There are a few reasons why you might want to do this, but whatever your reasons, it’s essential to be aware of the consequences.
First of all, bypassing the neutral safety switch can be dangerous. You could get seriously injured if something goes wrong while you’re riding. Not only that, but you could also damage your ATV.
So, before you decide to do this, make sure that you understand the risks involved. If you’re still not convinced, maybe it’s best to leave things as they are and stick to the safe option.
Should You Bypass the Neutral Safety Switch on Your ATV?
You may be wondering, “Should I bypass the neutral safety switch on my ATV?” The answer to that question depends on your specific situation.
For example, if you’re having trouble starting your ATV, the issue may be with the neutral safety switch. Bypassing the switch may solve the problem.
However, if you bypass the neutral safety switch and something goes wrong, you could injure yourself or damage your ATV. So, it’s essential to weigh the pros and cons before making a decision.
ATV Won’t Start After the Neutral Safety Switch Bypass
When the engine is running, the neutral safety switch is on. The neutral safety switch automatically shuts off the ignition switch when you shift into reverse.
If you’re in neutral and trying to start your ATV, but it won’t crank, check the battery first. If your battery is fully charged, there’s a problem with your starter or starter solenoid.
If you have a problem with your starter or starter solenoid, follow these steps:
- Disconnect the negative cable from your ATV’s battery.
- Turn off the engine and allow it to sit for at least 10 minutes before reconnecting the cables to their terminals. This will allow any residual energy stored in them to dissipate before connecting them back to their terminals.
- Remove your ATV’s air filter by removing two bolts that hold it in place under where the rear fender meets the body of your vehicle and remove it from its mounting bracket.
- Remove the battery cables from the starter.
- Disconnect the negative battery cable from the positive battery post.
- Remove the starter cover by prying it off with a screwdriver or other similar tool.
- Locate your starter and use an Allen key to remove it.
- Remove the old brushes and replace them with new ones.
- Reinstall the starter in reverse order of removal.
Conclusion
There you have it! Now you know how to bypass the neutral safety switch on ATV. There’s no need to panic if you ever find yourself in a situation where you need to bypass the neutral safety switch on your ATV. By following the steps in this guide, you’ll be able to get your vehicle moving again in no time.
Also Read: How to Bypass Kill Switch on ATV- A Beginner’s Guide
Just be careful, and make sure to read the instructions carefully before you start meddling with your vehicle. All the best.
